A corded 185 mm / 7-1/4 in saw with a simple trigger, separate depth and bevel locks, and no inherited MGA electric brake.

Depth control

The depth-guide lever locks the base; no more than one blade tooth should project below the workpiece.

Bevel and sighting

A separate lever locks actual bevel; the 22.5°, 45° and 56° selector sets the range. A is the straight-cut reference and B is the 45° reference.

Trigger and lamp

Pull the trigger to run and release to stop. The lamp stays on whenever plugged in; it is not a trigger-only indicator.

Support and stopping

Use front and rear grips and keep the wide base on supported retained wood. The MG coasts; wait for standstill and guard closure before placement.

Check before you follow

Identity & documentation.

Brand
Makita
Model
5007MG
Tool type
Corded circular saw
Market
US product identity with exact 884671-946 owner-document gate
Evidence level
Manufacturer documentation; no physical testing

A source check date records this research pass. It does not confirm that a manual is the newest possible revision, a tool is still in production, or a particular unit matches these documents.

884671-946; manufacturer-hosted primary, current supplied-revision bridge unclaimed.

Keep the limits in view.

  • Actual nameplate and supplied instructions must match.
  • Existing correctly installed approved wood blade only; no assembly conversion or service recipe.
  • No inferred latest supplied revision, weight superiority or high-angle capacity resolution.

Read the instructions for the tool and any applicable battery or charger together. Routine owner care stays outside the housing; internal service belongs with the manufacturer or an authorized service provider.

Makita: explore this brand’s tool references

Guides for this model

Explore controls, comparisons and documentation for this exact model.

  • 5007MG versus MGA stopping

    A documented selection framework for the exact US pair: shared controls and square capacity, MGA-only braking, guard and isolation requirements, and unresolved specifications.

  • Verified straightedge offset

    Use a supported disposable sample to establish the selected base-edge-to-retained-cut offset, position a straightedge and verify a finished width with the 5007MG.

  • 5007MG supported end cut

    An exact-model existing-owner workflow for the 5007MG: original assembly, automatic guard, zero bevel, limited tooth projection, retained-side support and complete standstill.

  • Large-panel support plan

    Plan retained-piece support, offcut stability, an unobstructed blade corridor, independent clamps and cord clearance, then accept both the cut pieces and the support layout.

  • Measured-kerf layout worksheet

    Account for every finished length, end-preparation loss and real separation kerf before accepting a circular-saw layout.

  • Used-saw reject, hold or consider

    Build a documented pre-purchase decision from exact model identity, isolated external checks and unresolved assembly or service questions, without a powered fault test.

  • Two ends, one verified length

    Use a qualified 5007MG to establish one square datum, rebuild the second supported setup and accept the final board by length and squareness—not by two completed cuts.

  • Slow guard return: use or service hold

    Complete an unpowered lower-guard assessment, distinguish an observation from a repair diagnosis, and document the conditions that keep a 5007MG out of use.

  • Dark cut edges: correct or hold

    Separate a dark-edge observation from a diagnosis, check documented blade and setup mechanisms, and decide whether one controlled wood sample or a service hold is appropriate.

  • Plywood blank: width first, final length second

    Qualify a straight reference and long-feed support, rip one plywood blank, check width at three locations, then finish and accept its square length without implying a shelf load rating.

  • 5007F versus 5007MG control habits

    Compare exact lamp behavior, bevel locking mechanisms and documented square capacity, then make a model-specific ownership choice without borrowing brake or accessory claims.

  • Rail versus straightedge system choice

    Compare the measured offset of a 5007MG straightedge setup with the qualified fit and trimmed reference of an SP6000 rail, then choose by support and acceptance evidence.

  • Known wood: accept, hold or choose another piece

    Identify the actual workpiece, inspect fastening and condition, establish material precautions and blade suitability, then label whether it can proceed to isolated saw setup.

  • Blade side and supported-base layout

    Normalize two documented saw views, locate the broad retained-base support and guide contact, then rehearse a complete isolated layout without inventing handedness rules.

  • A complete accessory budget

    Build an owner-priced readiness ledger that separates verified reuse, missing prerequisites, optional items and unresolved compatibility without inventing prices.

  • Workspace admission

    Map the actual work, supported separation, operator travel, supply route and bystander controls, then decide whether this location can host one documented task.

  • Plywood edge bevel

    Plan long and short points, set the MG positive stop and recalibrate the bevel guide before accepting the full plywood edge.

  • Misaligned-cut recovery decision

    Use the exact MG stop-and-withdraw instruction, identify the cause and decide whether enough supported stock remains for a separately accepted new cut.

  • Known-owner return from storage

    Build a complete change-and-condition record for an existing 5007MG, including storage events, original assembly, supply and workspace, without a live fault test or invented service interval.

  • Angled end, square blade

    Complete a 45-degree face-mitre blank with explicit datum, diagonal support and guide clearance, then accept both point lengths, angle and square-through-thickness edge.

  • Choose a complete cutting route

    Use exact 5007MG and FX4111 documentation to choose a supported whole-board cut, qualified localized task or evidence-based hold.

  • Six blanks, not a finished nestbox

    Plan and inspect a source-dimension six-piece wooden kit, including complementary side slopes and a safely supported small floor, only after local design and actual roof acceptance.

  • Paired platens and a stable drying stack

    Plan long-stock cuts, accept two matching flat plywood faces, then build the RHS clean dry A4 layers with its book-weight alternative, without drilling or claiming a load rating.