Model reference Documented regional identities

Metabo
by the model.

Explore documented models by tool family. Match the actual regional identity and complete instructions before using any model-specific guidance.

Identify your tool

Circular saws

Explore the collection

Corded circular saw

KS 55 FS

A complete documented square-wood setup using the already correctly installed original blade assembly, model-specific controls and suitable connected extraction.

Model, manuals & limits

Corded circular saw

KSE 55 Vario Plus

The 01204000 owner system separates depth preselection from motor locking and uses a double parallel stop, variable wood speed and a clutch-dependent original blade assembly.

Model, manuals & limits

Corded circular saw

KS 85 FS

A 235 mm corded saw with a movable 2.2 mm riving knife, half-tooth depth recommendation, two bevel locks and double parallel guide; the matched owner workflow stays square and excludes plunge cuts.

Model, manuals & limits

Cordless circular saw

KS 18 LTX 66 BL

A half-tooth depth limit, two fence clamps, an eight-position dust connector and the current three-signal shutdown distinguish this original-assembly owner task.

Model, manuals & limits

Cordless plunge cut circular saw

KT 18 LTX 66 BL

Qualify the original assembly and complete base support, distinguish depth edge 10 from FS 9, central glass guard and seven-position extraction, then use the documented guarded-head start and actual stopped removal.

Model, manuals & limits

More guides for this brand

Metabo KS 55 FS: establish a supported square-cut setup

Check the 00955-series KS 55 FS depth lock, twin bevel screws, right-entering fence and secured extraction before a supported wood sample.

Explore the collection

Metabo KSE 55 Vario Plus: set both depth controls for a supported parallel wood cut

An exact 01204000 owner workflow covering original clutch assembly, separate depth preselection and motor lock, half-tooth projection, double fence and wood-speed signals.

Explore the collection

Metabo KS 85 FS: keep the riving knife, half-tooth depth and double fence working together

Qualify the original regional blade and riving knife, check both knife clearances, set half-tooth depth and two bevel locks, then verify the double fence and indexed extraction nozzle.

Explore the collection

Choose a replacement circular-saw blade by the complete specification

Build a complete blade-selection record for diameter, bore, speed, material and riving-knife constraints, with exact regional examples and stop outcomes.

Explore the collection

KS 18 LTX 66 BL EU: a square sample under the 0526 instructions

Qualify the original EU assembly, lock half-tooth depth and both fence clamps, route indexed extraction and interpret current shutdown signals without a restart tutorial.

Explore the collection

Metabo KS 55 FS or KS 85 FS: qualify the job, original assembly and ownership obligations

Compare actual depth needs, the KS 85 FS riving-knife conditions, distinct parallel guides and real supply/support/extraction requirements without ranking safety or inventing fitting procedures.

Explore the collection

Metabo KT 18 LTX 66 BL UK: a supported base-on-stock wood sample

Qualify the exact 01866001 original system, ordinary depth reference, central glass guard and seven-position extraction before a complete supported straight sample and stopped acceptance.

Explore the collection

KS 66 or KT 66: qualify the actual cordless owner system

Choose between the exact EU KS and UK KT systems by supported entry, complete clear finish, original assembly, controls and qualified dust/power—not a shared 66 mm headline.

Explore the collection

Identify your tool

Oscillating multi-tools

Explore the collection

Cordless oscillating multi-tool

MT 18 LTX

Legacy type 13021 has upward battery removal, a spring-pin cam holder and separate tool, battery and charger signals.

Model, manuals & limits

Corded oscillating multi-tool

MT 400 Quick

Cammed accessory holder with a removable spring pin and lever that must close against the housing, plus explicit OFF action after interrupted mains power.

Model, manuals & limits

More guides for this brand

Legacy MT 18 LTX: understand the clamp, charging pair and three signal sources

Qualify 625596000 and ASC 55, remove the pack upward and distinguish restart inhibition from low charge and charger warnings.

Explore the collection

MT 400 Quick: a fully seated pin, flush lever and deliberate OFF

Match the 0122 corded body, qualify the RCD supply, complete the spring-pin clamp and cut supported wood without assuming restart protection or blade-hood extraction.

Explore the collection

Metabo Q SL: quarter-turn pin and a complete triangular sanding setup

Match the Austrian 13088 body, turn the spring pin correctly, secure triangular-pad extraction and finish a clamped wood sample with a clear acceptance check.

Explore the collection

Identify the exact oscillating tool, region, revision and sale package

Separate machine labels, regional service identities, manual revisions and actual bundle contents before choosing an oscillating-tool owner workflow.

Explore the collection

Compare oscillating-tool specifications without inventing a performance ranking

Use exact GOP18V-34 and MT 400 Quick source values to normalize angle notation, separate unlike quantities and produce a defensible requirement-based shortlist.

Explore the collection

FEIN AMM 300 Plus or Metabo Q SL: choose the complete sanding system

Compare exact clip-in and quarter-turn pin responsibilities, pad-specific settings, dust scope and separate power systems before a small-wood sanding project.

Explore the collection

A loose oscillating accessory: isolate, identify and decide

Distinguish a snap holder, threaded bolt and quarter-turn spring pin before correcting a documented omission or handing an unresolved defect to qualified service.

Explore the collection

Legacy Metabo MT 18 LTX or Q SL: choose the complete owner system

Choose whether to retain documented OIS inventory or complete a StarlockPlus system, including the different pin action, actual power identity and sanding extraction.

Explore the collection

Find your next answer.

Search guide titles, summaries, brands, and model names.

Tab to a result · Enter to open · Esc to close